Search results

what are yout channel volumes set at? I used to get that sound when turning the channel volumes too loud. Ive had this problem before. I went away after I changed the tubes. duh!. :roll:

try putting a patch cable between the send and return of the fx loop. it makes the amp just a little tighter and a little faster. it will make the notes seem to come out easier from the guitar where as before you kind of have to push to get them to ring out and sustain with the patch cord in the...

I like stock mesa 6l6 with bias switch set to el34. or el34 tubes. I cant really decide they both sound great. get both :lol:

the width of the actual gear that can fit into a rack is betwwen the rails is 17-3/4" the rest is rack ears it adds up to 19". the problem is that the triple rec pcb that the amp is built on is wider than that. you would have to gut the amp completely and rebuild it all by hand into a new...

the diodes and spongy change the feel of the amp not so much the sound. imagine your amp responding slower to your pick attack for rhythm keep it bold, and diodes the master on each channel is there to balance the volume on the channels so they are the same when you switch between them output...

ok ok try this: bass 9:00 mids 1:00 treble 1:00 gain 12:00 or 11:00 presence depends on your cab, stand off to the side of the cab if its too much I think a darker cab might do it some good IMO

just looking at your settings: the high bass setting will murder your harmonics. turn off the lights when you play and twist the knobs on that channel until it sounds how you like it whatever you do don't look at those **** knobs. what you see will mess with what you hear. there must be a...

http://www.myspace.com/romansidorov I recorded everything on there with a single rec. Excuse the overall sloppiness, but that should give you an idea of the sound.

The el 34 setting is "pretty much" the correct bias for 6l6 tubes. Bob at eurotubes seems to think so too (thats where I got the idea from). Ive been doing it this way for a few months on my Solo 50 and its fine.

try setting the bias to el34 while running 6l6 powertubes. the hotter bias makes it sound MUCH bigger and warmer.

that is correct

I found that switching the bias switch to el34 while running 6l6 tubes makes a big difference too. It makes the whole amp sound warmer and bigger to my ears. Seems like its not damaging. Ive been running it that way for several months. It might decrease the tube life span, but it sounds much...

single rec old or new do not have spongy or bold settings the only thing on the back pannel is the fx loop to hear the amps intended sound get some stock mesa tubes in it. then you must spend A LOT of time playing with it. It took me about a year to figure out my single rec and there are...

I would love to hear what you think about the differences between the two

Ugmo Does the pedal add noise in YOUR rig? is that a problem for YOU? Being a triple rec I doubt you ever get the volume turned up too high on it so the poweramp should be staying pretty clean for all your playing even if your playing "loud" your probably using only about 25% of the volume that...

I don't know how exactly you guys are able to hear one individual's rig by reading the amp settings. It doesn't sound like a question about tonal advice. He even posted a clip of his current sound, and said that he is quite happy with the sound hes got going on right now. How about you tell him...

its passive the presence cuts the highs after the preamp in the power amp section. I suppose you could replace the presence pot with a resistor of the same value then it would be locked in place in that one setting. it would free up the presence knob.... it sounds like you are talking about...

That the way any passive control works. a pot is a variable resistor turning it up reduces the amount of resistance. Supposedly the only difference between the red and orange channels is that the presence pots are different values.

turning your presence all the way UP would be close to taking it out of the circuit so leave that knob there if you like the sound when the presence is all the way down. leave it alone I would sooner have the loop modded to get rid of the undesirable coloration, and run an eq in the loop if...